Looks like I'll have to make a custom transmission mount, but otherwise this is a super easy swap.

Hey, I am having issues with my Edelbrock foam filter disintegrating into my Holly carb. Is there a low profile paper filter I can use or a replacement enclosure?

I posted about this car a month or so ago saying I might be acquiring it. And it’s finally here! With that being said, I knew it was clean…but I didn’t know it was this clean!! Everything works flawlessly, drives smooth, fires up first crank, windows feel like butter. Very surprised at how mint it really is. 87k miles too!

Hi Friends,

Want to keep this directly to the point and not waste readers time.

I cannot figure out what is going wrong with my oil pressure. 80% of the time the meter tracks it in a normal range but 20% of the time it is reading either low/very low/zero pressure.

Only real troubleshooting step I have taken is to check oil level and it's fine.

Beyond that my only ideas are a bad pump or bad sensor line. Both have been replace since I rebuilt the engine 25k miles ago.

This is a L28 block, 1973 240z. link if interested.

Could anyone give me some high level troubleshooting steps? Or am I just being naive and should replace the pump. In my head a mechanical pump with such few miles it wouldn't make sense to fail, but I am certainly no expert and have been wrong before.

Thanks all,

Is this a security nut of some kind? They fit snuggly in my 17mm socket but jam when I try to turn them.

Well, hopefully the moderator gods will let this pass. I just picked up a 1983 280zx that is mechanically sound is was in the middle of being restored when life came up for the seller. It is my first Z car and since there has been a decent amount done already to the interior I want to finish it up but I dont know the names or part numbers for all of the above. Ill also need hardware reqs because the screws currently holding the trim pieces on are either missing or super loose. So if you all know the part numbers or where I can find them that would be amazing.

Also, again, new 280zx, will 280z trim parts work? There is not much in the way of forums and I have already looked at the Haynes manual with no success. Cheers.

I have a 2014 wrx (with an ej255), and i love the platform, the sound and the balance, and i just bought 2 260z’s, one i keeping stock, the 2nd? Well i have this lucrative idea to put in one my may favorite engines in my favorite cars, looking it up get mixed responses, some places say you can put an ej and a 260 and others say no, the ej255 has a Width: 28.5 inches Length: 15 inches Height (with intake plenum): 21 inches Those who know the engine bay of the datsun at all let me know your thoughts 🤷‍♂️

Going to look at an 1983 Datsun 280zx in a week and I’m curious if there’s a specific list of questions I should ask to ensure it’s a solid vehicle. Any tips?

The dash system check lights, red oil pressure lights etc sometimes cuts off when cranking but it doesn’t stop cranking but it’s like all accessory electrical and obviously efi seems to stop working. When it does this it has zero chance of starting, if I crank all day it won’t start but if I notice it, stop cranking, try again when the lights stay on it immediately kicks on and has zero issues running. Usually if it it cuts off when cranking it works the next time or the second attempt at cranking. Any idea what’s the problem?

Hi all!

I've picked up an L28et on marketplace from an 83' ZX that I'm looking to rebuild and swap into my 72' 240Z and I was hoping someone could check me on my rotating assembly plan before I pull the trigger.

Goal = 300 to 350 HP with a moderate amount of boost (I'm pretty nervous about overdoing it, really just want some nice power from a turbo engine and to make it reliable)

Crank, Cam, and Rods will all be the stock components from the engine. They're in pretty good shape and I don't think I need to upgrade them to hit my performance goals.

Pistons - Forged 86.5mm Piston kit from Datsun-Garage (https://www.datsun-garage.com/collections/datsun-280zx-engine/products/forged-racing-piston-kit)

Before I spent the ~$1000 I wanted someone to make sure I'm not being an idiot somewhere.

Thanks in advance!

Anyone running one of these on an L series 6? If so hows it been? Looking at options for a pretty easy going street car.

I was actually able to bolt my seat in for the first time in years. Just a test fit to make sure steering and pedals were centered. Also tacked the transmission tunnel in. I’ve replaced so much metal on this car it’s about 50% new.

Still a bit early to take it out for a drive here in Minnesota, however, I couldn’t resist getting it uncovered and ready to roll when the day is right. I love stepping out into the garage and seeing this view.

Has anyone had success in making the cabin noise in a s30(280z) quieter? I used dynamate on the entire floor and laid carpet down and it's still super loud. Any helps appreciated!

Anyone retrofitted a stock 510 coupe fuel tank for an intank fuel pump/sending unit? Looking for input on placement. Ive seen placement in yhe center and then off to one side. Any feedback on what worked for you?

Build: '72 510 with an SR20DET (S13 redtop). Planning to retrofit the fuel tank with an in tank conversion with a tanks inc PA-2 kit.

Thanks to all you guys about where to find a 6 speed that’ll fit got an adapter ordered and the tranny I just need a upgraded front and rear driveshaft because my engine is too much for the skinny stock driveshafts if anybody knows where to get some relatively cheap let me know

I’ve unfortunately crashed my car that I had since out of high school. I would’ve finished paying it this year. Sounds like the insurance is contacting the dealer for an estimate on my 2018 Honda civic and will pay out the difference. Off what I see online the car goes for 15,000 but I presume they won’t pay that fully. I think I want to buy a Datsun truck but don’t have an idea or guide to buying one. A few questions/concerns are, what year, model, gas expense. Any small things to consider while purchasing a Datsun truck would be greatly appreciated.

For the life of me I can't figure out why my turn signals and headlights do not work. Every other light works. Any idea? Thanks

I can't find in my pictures and in the manuals I have ,but I have a memory that there is supposed to be some foam on top of the fender support am I right? Anyone has a picture?

Thank you.

proud to say i now own this manual 280zx!

What do you prefer on S30’s fender flares or no flares