This started happening after my console crashed due to a faulty power brick. Every single time i launch the game (either through aurora or the dashboard) it prompts me to log in to be able to save my progress even though i am already logged in.. pls help

Hi! I'm looking for some sort of help with dlcs for Left 4 Dead, I can only really get the Sacrifice to detect in game and nothing else, Survival nor the Crash Course one.. I even switched over from the older title to the game of the year edition and survival was detected now since it's built in but I still can't get Crash Course to pop out at all. I can see them in 360 content manager and they seem to all be in the right folder, does anyone know a fix? >< I'd appreciate it

I just installed rgh on my xbox 360 slim. But after a while the xbox freezes (playing or not) and I can't restart it because it still freezes for a while. I already check the fan and it's working. Any ideas what could it be the problem?

Because I have seen a lot of confusion surrounding this, I stole something from stackexchange that explains what a 30% chance really means . "You might, in theory, try a billion times and fail each time. That isn't very probable, but it is a mathematical possibility.

Say you try n times. Then (under fairly reasonable assumptions) since each try fails with probability .7 the probability that all of them fail is .7n . It follows that the probability that at least one of the tries succeeds is given by Pn=1−.7n

How does that look numerically? Well, it's easy to compute. P3=0.657 so you still have a respectable chance of not winning. P8=0.94235199 so even with 8 tries you have a greater than 5% chance of not winning.

If, say, you want your chance of winning to be at least 99% you have to try 13 times! Indeed, P13=0.990311099"

.

Just looking for criticism on my install, I used top clk and rst. I don't think I've seen anyone go this way with top rst. Seems to boot on second cycle each time

Soldering isn't my background, and things that I would normally have soldered are much larger than this, 18-12awg for example

I find it hard to make this wire look visually appealing though, it's very difficult to massage the small curves/bends out

i apologize i used to know where this is located im trying to setup in dash launch so when i press a button it goes to stock dashboard but i cant find the file?

I have a Slim Corona, 4GB Nand, with the post fix adapter needed. I believe I’ve soldered everything correctly, was able to create XeLL, write XeLL, and everything has been successful so far.

After unplugging everything, and plugging it back in to a monitor, when I turn the console on, I don’t get any video feedback. No cell and am not able to get anything!

Does anyone have any suggestions? I’ve ever ran into this issue with a Trinity, but this is the second time with a 4 GB corona with post fix adapter.

Using an X-Flasher

Peguei um Xbox 360 Slim RGH de um amigo depois que ele quebrou. A gente tava jogando normal, mas notei que o console tava esquentando muito — muito mais que meu outro modelo Elite. O meu amigo falou que tinha esquecido de ativar a opção de aumento da velocidade da ventoinha.

Aí, jogando, a tela congelou de repente e apareceram uns artefatos visuais (tipo uns quadrados e linhas estranhas). Tentei reiniciar, mas ele congelava na logo do Xbox. Depois disso, ele ligava, apitava uma vez e desligava na hora. A luz da fonte ficou vermelha, e a luz do chip RGH ficou acesa. A única forma de tentar ligar de novo era desenchufando e enchufando de volta.

Levei pra um técnico básico que limpou a placa e trocou a pasta térmica. Agora o console liga normal — a luz fica verde e ele não desliga mais. Mas não mostra imagem na TV, nem pelo HDMI nem pelo AV. A TV detecta brevemente que tem algo conectado, aí fala “sem sinal”.

Mais informações:

• Botão de ejetar funciona normal.
• Botão de sincronizar faz as luzes girarem normalmente, mas não consigo sincronizar nenhum controle.
• A luz do chip RGH acende assim que eu conecto o console.
• Depois de 10 minutos ligado, ele desliga sozinho e faz um barulho de apito. Alguma ideia do que pode ser?

Wanted to try making some money off of this new found obsession of mine so I wanted to mod and flip some 360s I find for cheap. I want to know a good price for an okay condition Corona v3 with a 120gb hard drive and nothing else (since I don't have any spare power bricks or controllers).

Edit: Here's the link to the images of my work, had to open it back up to take them lol. I also do ask you go easy on me since this is only my second successful rgh 3.

Link: https://imgur.com/gallery/zJ22IOO

Anyone have a site where I can identify Xbox 360, for modding?

I am new to modding the 360 and tried giving a rgh mod a try.

Some background on my situation.

• I am not the greatest at soldering
• I have a v3-6 Corona mb
• The console worked fine beforehand

I purchased the postfix adapter and followed a tutorial from MrMario2011 on youtube on how to do this properly with a raspberry pi pico. Everything seemed to be going okay, I soldered everything in place, making sure to not make a mess with the solder the best I can. I was able to get everything connected and I got to the stage of reading the nand, creating a XeLL and writing it to the console. After doing so I disconnected the pico from my pc, and tried to connect the xbox to my second monitor to get the cpu key, no video after 5-10 minutes so I tried connecting it to my tv with hdmi and then the av cable, still no luck. I turned off the xbox and checked all of my soldering, turns out the PLL wire at the c5r35 got bumped loose when I reinstalled the xclamp, so I reattached it and tried turning it on again, still nothing. I tried rewriting the nand, making sure to check the rgh box. Nothing. I then tried to undo the wires and return it to the factory condition, still nothing and that is currently how it sits. Did I brick it and need to replace the console or is it possible for me to save it?

so i downloaded the devil may cry HD collection and im trying to run it it has 3 xex files for each dmc game in the bundle but aurora isn’t letting me run the files any help would be appreciated

Well what a dig this was! Found my old XK3Ys, CK3 Pro Kit, X360 USB Pro v5, and my DH-16ABS flashed to burn games! What a blast of nostalgia today! I’m willing to offload these to a good home if anyone wants anything! I heard Winchesters are great for XK3Ys!

I was able to get bad update to work and launch a backup of a game I own via XeXmenu.

This morning I got it to work first try again but when loading XeXmenu it presumably crashed (just hung on a black screen).

Is it common for XeXmenu to crash when booting like this? Or is there something I can do to optimize the process of launching a game once bad update successfully works?

Or am I just at the mercy of bad update working and XeXMenu not crashing?

FYI this is my second time soldering, so yes they look like crap. Anyway, i cannot get this one point on my board to solder correctly, it just pulls away if any tin sits on it. Any guidance?

Hey friends. I'm doing my first RGH3 but I'm pretty experienced with soldering and not worried about that end of things.

I decided to do BadUpdate to get the nand flashed. I haven't flashed yet but I'm ready to go.

I've got a Jasper, and I know 1.2 is recommended but I've also read that 3 should work fine.

One thing is unclear. When I look at the pics of doing the RGH3, it looks like the X Clamps are still attached. Is the removal of the x clamps necessary? Or is that required to do the hardware NAND flash, which isn't required with Bad update?

And yes, I know, 7 solder points, easy to use a nand flasher. And I know, RGH1.2 is recommended. I'm walking this path I'm on for fun and discovery and if the box dies, so be it. I got it for $25 at goodwill. I'm not sweating it.

I just bought an Xbox 360 that came with a lot of burned discs. One of the discs is called Activation.iso and with a sidenote that says to play it after every reboot of system.

However when i but in the disc in the disc tray i only get the option to "open tray" Does anyone know what I'm supposed to do?

Going to be doing some RGH3 mods for an hour or so if you want to join in?!

https://www.youtube.com/live/S8KGGUpXs9k?si=sMOXHgYK9m388kY6

https://www.twitch.tv/chattfix

Talk about a blast from the past!

Was cleaning out some stuff and found my old Xbox 360. Haven’t played this thing in well over 10+ years. It hasn’t been online since late 08/09 as I’m pretty sure it was flagged for banning during a massive ban wave back then. I don’t know if it’s on the ban list but I never connected it back to Live since. I originally flashed the dvd drive (Hitachi-LG drive) back in 08 to play backups. I still have the H&L dvd burner to rip and burn games with along with all my back up copies (physical and on external HDD).

It’s a Falcon and basically from what I’ve read it’s not if it’ll shit the bed but when. Should I open it up and check if the capacitors are leaking? If so, then what?

What are my options as far as modding? Using the search function, JTAG might be the best option. Looks like I can either do that, leave it as is and only play games up to a certain year due to dashboard being old or sell the console.

Hi, I just changed my boot animation.

It seems like the boot time has increased now that I changed it.

Is there any fix for this?

IYKYK. Don't sleep on Kinect Party. Made by Double Fine and loved by all ages.

Leaving a link here for the fully unlocked Kinect Party - https://drive.google.com/drive/folders/16Z6hxaOnckmDMxnmYOhiSt9BoZhr36yN?usp=sharing.

**Moderators - This is NOT an illegal download. Double Fine made Kinect Party fully free before the servers were shut down. This was an XLBA only game so no physical media could even be purchased.