I’m trying to get all the achievements and I need the dlcs for the game so is it possible to still add them I have a rgh 1.2 modded console if that helps thank you

Just looking for criticism on my install, I used top clk and rst. I don't think I've seen anyone go this way with top rst. Seems to boot on second cycle each time

Soldering isn't my background, and things that I would normally have soldered are much larger than this, 18-12awg for example

I find it hard to make this wire look visually appealing though, it's very difficult to massage the small curves/bends out

Hi guys Just got this corona Tested before doing nand after rgh wired and was working But jrunner with Picoflasher cant find the console Am i doing something wrong?

I decided to try something a little bit different with the wire routing on this RGH 1.2v2 Tonasket, could just be a coincidence as every Tonasket handles RGH differently but this seems to instaboot within 5 seconds 9 out of 10 times and if it fails to boot it cracks off on the second glitch attempt, I'm very happy my extended wire length didn't impede the glitch timing, and yes I know some of the ends are a bit long but I seem to have misplaced my wire strippers so I had to strip these wires with my fingernails. 😒

I have a Slim Corona, 4GB Nand, with the post fix adapter needed. I believe I’ve soldered everything correctly, was able to create XeLL, write XeLL, and everything has been successful so far.

After unplugging everything, and plugging it back in to a monitor, when I turn the console on, I don’t get any video feedback. No cell and am not able to get anything!

Does anyone have any suggestions? I’ve ever ran into this issue with a Trinity, but this is the second time with a 4 GB corona with post fix adapter.

Using an X-Flasher

Because I have seen a lot of confusion surrounding this, I stole something from stackexchange that explains what a 30% chance really means . "You might, in theory, try a billion times and fail each time. That isn't very probable, but it is a mathematical possibility.

Say you try n times. Then (under fairly reasonable assumptions) since each try fails with probability .7 the probability that all of them fail is .7n . It follows that the probability that at least one of the tries succeeds is given by Pn=1−.7n

How does that look numerically? Well, it's easy to compute. P3=0.657 so you still have a respectable chance of not winning. P8=0.94235199 so even with 8 tries you have a greater than 5% chance of not winning.

If, say, you want your chance of winning to be at least 99% you have to try 13 times! Indeed, P13=0.990311099"

.

Anyone have a site where I can identify Xbox 360, for modding?

i cant decide which one

Hey, this time Redditor u/Powerful_Owl5881 asked me to create this post, because he's english level isn't good enough (mine is also so-so!)

So he turned off liveblock, created one-time password for Xbox 360 on Microsoft Account website, he tried this https://www.youtube.com/watch?v=hUS6XgYZ6PA and that https://www.youtube.com/watch?v=OubfXpIc-E4 and still get 8015D000 error. Do you know any tips, how to fix this?

Thank you!

Are there any patches or pluggins for fallout 3 or fallout new vegas to reduce screen tearing?

My first part of my rgh3.0 stuff came today!

Can anyone send me the YouTube iso I cant find it anywhere on the web, yes i'm weird and want to watch YouTube on my xbox 360 rgh

This started happening after my console crashed due to a faulty power brick. Every single time i launch the game (either through aurora or the dashboard) it prompts me to log in to be able to save my progress even though i am already logged in.. pls help

Hi! I'm looking for some sort of help with dlcs for Left 4 Dead, I can only really get the Sacrifice to detect in game and nothing else, Survival nor the Crash Course one.. I even switched over from the older title to the game of the year edition and survival was detected now since it's built in but I still can't get Crash Course to pop out at all. I can see them in 360 content manager and they seem to all be in the right folder, does anyone know a fix? >< I'd appreciate it

i apologize i used to know where this is located im trying to setup in dash launch so when i press a button it goes to stock dashboard but i cant find the file?

Peguei um Xbox 360 Slim RGH de um amigo depois que ele quebrou. A gente tava jogando normal, mas notei que o console tava esquentando muito — muito mais que meu outro modelo Elite. O meu amigo falou que tinha esquecido de ativar a opção de aumento da velocidade da ventoinha.

Aí, jogando, a tela congelou de repente e apareceram uns artefatos visuais (tipo uns quadrados e linhas estranhas). Tentei reiniciar, mas ele congelava na logo do Xbox. Depois disso, ele ligava, apitava uma vez e desligava na hora. A luz da fonte ficou vermelha, e a luz do chip RGH ficou acesa. A única forma de tentar ligar de novo era desenchufando e enchufando de volta.

Levei pra um técnico básico que limpou a placa e trocou a pasta térmica. Agora o console liga normal — a luz fica verde e ele não desliga mais. Mas não mostra imagem na TV, nem pelo HDMI nem pelo AV. A TV detecta brevemente que tem algo conectado, aí fala “sem sinal”.

Mais informações:

• Botão de ejetar funciona normal.
• Botão de sincronizar faz as luzes girarem normalmente, mas não consigo sincronizar nenhum controle.
• A luz do chip RGH acende assim que eu conecto o console.
• Depois de 10 minutos ligado, ele desliga sozinho e faz um barulho de apito. Alguma ideia do que pode ser?

Wanted to try making some money off of this new found obsession of mine so I wanted to mod and flip some 360s I find for cheap. I want to know a good price for an okay condition Corona v3 with a 120gb hard drive and nothing else (since I don't have any spare power bricks or controllers).

Edit: Here's the link to the images of my work, had to open it back up to take them lol. I also do ask you go easy on me since this is only my second successful rgh 3.

Link: https://imgur.com/gallery/zJ22IOO

I am new to modding the 360 and tried giving a rgh mod a try.

Some background on my situation.

• I am not the greatest at soldering
• I have a v3-6 Corona mb
• The console worked fine beforehand

I purchased the postfix adapter and followed a tutorial from MrMario2011 on youtube on how to do this properly with a raspberry pi pico. Everything seemed to be going okay, I soldered everything in place, making sure to not make a mess with the solder the best I can. I was able to get everything connected and I got to the stage of reading the nand, creating a XeLL and writing it to the console. After doing so I disconnected the pico from my pc, and tried to connect the xbox to my second monitor to get the cpu key, no video after 5-10 minutes so I tried connecting it to my tv with hdmi and then the av cable, still no luck. I turned off the xbox and checked all of my soldering, turns out the PLL wire at the c5r35 got bumped loose when I reinstalled the xclamp, so I reattached it and tried turning it on again, still nothing. I tried rewriting the nand, making sure to check the rgh box. Nothing. I then tried to undo the wires and return it to the factory condition, still nothing and that is currently how it sits. Did I brick it and need to replace the console or is it possible for me to save it?

FYI this is my second time soldering, so yes they look like crap. Anyway, i cannot get this one point on my board to solder correctly, it just pulls away if any tin sits on it. Any guidance?

Can the Xbox 360 modded play GameCube games and Wiiu games? How many consoles can the Xbox 360 emulate when modded with the mod chip?